OK...here's the pics from this mornings work...
First of all, I followed Pirtle's writeup step by step - So he gets the credit for putting all this down in the first place. Made things go smooth.

Last Weekend, I prefabricated the engine support using Andrew Olson's design. Went to Home Depot and got a 4X4 and had them cut it to 35.25" and a 37.25" lengths. The 35.25" piece goes up front and the 37.25" at the back of the engine. Also bought 1/2" X 10" eye bolts (w/nuts) and large washers. All the parts were about $22. I cut some scrap 2X4 into about 12" lenghts (4 of 'em) and counter sunk holes to fit over the fender bolt heads/washers so the 2X4s would lay flush. I removed the hood shocks to make room for the 4X4. Here's what they look like on the car with the hardware attached. THANKS again, Andew!
Name:  supports.jpg
Views: 197
Size:  74.4 KB

and here's where I connected the link's to the lift point (front)
Name:  Support.jpg
Views: 194
Size:  60.2 KB

I disconnected the battery and raised the vehicle as high as possible. About 20" from floor to lift point.
Name:  car height.jpg
Views: 193
Size:  66.3 KB

I removed the front wheels next although it would have been easier to loosen the lugs while weight was on wheels - so I had to use an impact wrench to get the wheels off once off the ground. Then I took off the oil filter and removed the 10mm bolt from the wiring harness.
Name:  step 8.jpg
Views: 191
Size:  49.0 KB

Next, I loosend the 19mm bolts connecting the sway bar to the drop links. I used a socket wrench with a very long hanele and made loosening bolts a lot easier.
Name:  step 9.jpg
Views: 191
Size:  73.4 KB

I took off the sway bar to body bolts and swung the sway bar down.
Name:  step 10.jpg
Views: 185
Size:  79.5 KB
Name:  step 10a.jpg
Views: 188
Size:  80.7 KB

Next, I loosened the four 13mm nuts holding the steering rack plate to the cross member
Name:  step 11.jpg
Views: 188
Size:  75.6 KB

Then removed the 17mm bolt on the plate to the left of the steering rack (driver's side)
Name:  step 12.jpg
Views: 183
Size:  72.6 KB


In order to get at the four 17mm bolts/nuts holding the steering rack, I used a short socket that came with the ratcheting wrenches. This worked great for getting into the tight places above the rack to counter hold the bolts
Name:  step 13.jpg
Views: 178
Size:  63.9 KB
Name:  step 13a.jpg
Views: 178
Size:  72.8 KB

I added a step to Pirtle's process at this point. Before dropping the steering rack, I needed to take out the PS line clamp on the driver's side fender - here's a picture of it - can be accessed either from top or below. Just follow the PS steel lines from the rack up the side of the engine bay and you should see it. I got to it from the top and used a 10mm ratcheting wrench.
Name:  step 13b.jpg
Views: 177
Size:  39.6 KB

Next, I removed the four 13mm nuts holding the rack plate in place and removed the steering rack plate.
Name:  step 14.jpg
Views: 177
Size:  72.0 KB

exposing the steering rack which can now be pulled down and maneuvered around.
Name:  step 15.jpg
Views: 177
Size:  77.2 KB
Name:  step 15b.jpg
Views: 178
Size:  72.1 KB

Then I loosened the 19mm nuts at the bottom of the motor mounts (under the cross member)
Name:  step 16.jpg
Views: 177
Size:  72.5 KB

And removed the 13mm and 17mm bolts that hold the mount housing to the engine block
Name:  step 17.jpg
Views: 176
Size:  76.6 KB


Next, I needed to lift the engine - about an inch. I removed the air box (both upper and lower halves when I put the 4X4 engine support across the engine compartment). I put masking tape on the engine support bolt threads after snugging the nut down by hand.
Name:  step 19.jpg
Views: 169
Size:  16.6 KB

Then tightened the nut until 1" of thread was exposed below the tape - make sure you check the clearance of the O2 sensor while lifting the engine. Mine was OK.
Name:  step 19a.jpg
Views: 169
Size:  20.0 KB

Next, I removed the lower motor mount nuts under the crossmember.
Name:  step 20.jpg
Views: 168
Size:  24.8 KB

Then came the INFAMOUS crossmember upper support bracket bolts. I was warned about these. Rather than counter hold the nut from above in the engine compartment (as was suggested), I used a long socket extension on the rearward nut (driver's side) and a regular socket for the front. The passenger side did not seem to have space issues.
Here's the front bolt (driver's side):
Name:  step 21.jpg
Views: 169
Size:  26.1 KB

and the rear nut (driver's side) using a long extension
Name:  step 21a.jpg
Views: 169
Size:  20.2 KB
Name:  Step 21b.jpg
Views: 168
Size:  22.6 KB

The driver's side come out easy by hand. But the Passenger side required tapping with a hammer and screwdriver. This one will be interesting to get back in.
Next, I loosened the front 17mm bolt on the tow hook at the front of the chassis and removed the 2nd (rear) bolt.
Name:  step 22.jpg
Views: 170
Size:  26.2 KB

Then I removed the two 19mm bolts at the end of the tow hook - these are the two bolts used to mount the front of the Lower Control Arm as well.
Name:  step 23.jpg
Views: 169
Size:  23.5 KB

The tow hook should then swing down freely.
Name:  step 23a.jpg
Views: 170
Size:  25.6 KB

Next, I removed the two 19mm bolts at the rear of the control arm mounts
Name:  step 24.jpg
Views: 168
Size:  20.1 KB

Finally, I removed the two 19mm bolts holding the cross member - one at each end.
Name:  step 25.jpg
Views: 170
Size:  22.4 KB

Then I maneuvered the crossmember down enough to remove the motor mounts. Then some additional maneuving to get the crossmember out completely.
Name:  Step 26.jpg
Views: 169
Size:  23.2 KB

After the motor mounts were out, I used the air impact wrench to get the upper bolt off the mount.
Name:  step 29.jpg
Views: 170
Size:  21.6 KB

Then I compared the old and new mounts side by side and looked for differences. The first obvious difference is mine's flattened. Second, it looks like I'll have to grind off the little pin in the top of the mount. And it looks like no pin to hold the mount in place while tightening on the new mount.
Name:  Compare.jpg
Views: 171
Size:  51.3 KB

I also looked at the clearance I had between the lower motor mount stud and the steering rack banjo bolts while the rack was in the car and noticed I would have very little room left for a longer stud on the new mount. So I compared stud lengths on the mounts and the new one is about 1/4" longer (actually about 3/16"). So rather than take any chances, I'll remove about 3/16" of the threads on the lower motor mount stud.
Name:  Threads.jpg
Views: 167
Size:  43.1 KB

Well, that's as far as I got this morning before I broke for lunch and posted these pics. Now it's back to work. I'll make the mods to the new mounts first. Then I'll do some cleaning - I actually missed a couple of bolts and there are areas on the crossmember I couldn't get to before so now's the perfect time to do some more cleaning before reassembly. It's
3:45 pm now - probably won't finish tonight but will check in before hittin' the sack....


Here's some pics from the progress made late yesterday on the MM mods and initial reinstall.

I used a dremel tool to cut the pin off the top of the new MM - went quickly.
Name:  pin delete.jpg
Views: 118
Size:  82.4 KB

Next, I measured about 3/16" and taped the new MM lower stud so it would be the same length as the original. The first one I used a grinding wheel to grind it down - took about 15 minutes. The second I used the dremel - took about 5 minutes.
Name:  MM threads.jpg
Views: 117
Size:  13.6 KB

When I began the reinstallation, it started with bolting the top MM bracket to the top MM stud and torquing it down to 62ftlb. Then getting the crossmember back into position with the heat shields still attached. After struggling with it for about 20 mintues with no progress, I decided to disconnect the passenger lower control arm from the lower shock mount and remove the sway bar as well. After that, the crossmember was in position in about 5 minutes with no hassles.
Name:  LCA Drop.jpg
Views: 121
Size:  105.5 KB

With the cross member close to position, I tilted it back toward the rear enough to insert/place the motor mounts (with bottom plate) bottom studs through the hole in the crossmember. This was the same way I took the MM out from the crossmember. I kept the bottom plate lined up by aligning the pin hole in the bottom plate with the alignment hole in the crossmember. Then put the washers and 19MM nut on just enough to keep the MM from coming out.
Name:  lower mm bolt.jpg
Views: 116
Size:  61.1 KB

At this point, I'm still holding up the crossmember. Next I maneuvered the crossmember with mounts attached up to the mounting holes in the engine block and placed the 17MM and 13MM bolts in and hand tightened. Now the crossmember was held up and I could work on getting other bolts aligned and installed while everything was loose.
Name:  MM bracket bolts.jpg
Views: 115
Size:  69.0 KB

Next, I installed the INFAMOUS crossmember support bracket 19MM bolt. I think the key to getting these back in is to do it when everything is nice and loose. The driver's side when in without a hitch - just pushed it in by hand. The passenger side needed a slight pull with the prybar to line the holes and a few taps with the hammer and it went right in. I did not torque these down yet.
Name:  support bolt.jpg
Views: 117
Size:  75.8 KB

Then I placed the 17MM crossmember to frame bolts (one at each end) and hand tightened. Then I went back and torqued the bolts in. Started with the MM bracket to engine block 17MM (33ftlb) and 13MM (17ftlb).
Name:  mm bracket T.jpg
Views: 117
Size:  84.6 KB

Next, I torqued the crossmember to frame 17MM bolts (one at each end - 33ftlb).
Name:  cross brace T.jpg
Views: 116
Size:  82.1 KB

And finally, I torqued the crossmember support bracket 19MM bolts (62ftlb).
Name:  support T.jpg
Views: 117
Size:  75.5 KB

That's as far as I got last night. So far, time on task working on disassembly and reinstallation only has been about 6.5 hours. Three more hours on top of that for cleaning and setting up the grinder. Now it's about
10:00am and I'm heading out to get the lower control arm back in and continue reinstallation.


Started at 10:30 this morning and finished at 1:30 this afternoon (3 more hours) bringing the total time on task to 9.5 hours - plus I took a lot of pics. I figure without the pic taking maybe 8.5 or 9 hours total - definitely doable in a day.

So here's the rest of the pics for the remaining install I did today...
Since I removed the LCA to get the crossmember back in, I had struggled with getting the lower shock mount to line up with the LCA bracket - too many things under tension. So this morning I tried a different approach and used the floor jack to hold up the hub/upper ctl arm while I maneuvered the LCA into place. Took about 10 min.
Name:  LCA install.jpg
Views: 135
Size:  84.8 KB

All I did at this point was insert the bolt with the stabilizer link on the back side to hold things in place while I re-inserted the lower ball joint stud in the steering knuckle.
Name:  shock bolt in.jpg
Views: 135
Size:  76.4 KB

The WSM recommends applying Optimoly HT (Copper Anti-Freeze, er Anti-SEIZE) to the Lower control arm bolts before putting them back in (both forward and rear LCA bolts)
Name:  apply HT.jpg
Views: 133
Size:  15.2 KB

This is what I'm using for Optimoly HT:
Name:  HT bottle.jpg
Views: 133
Size:  19.1 KB

And this is what I use for Optimoly TA (Aluminum colored anti-seize):
Name:  TA bottle.jpg
Views: 132
Size:  18.9 KB

I installed the rear LCA bracket first:
Name:  LCA rear - 2.jpg
Views: 131
Size:  63.7 KB

I only tighten the 19MM bolts 'til there's about 1/8" gap between the bracket and the crossmember. I read that this will allow the car to settle easier after weight on wheels and a short drive. Then I torque it down after the car settles:
Name:  LCA hand tight.jpg
Views: 133
Size:  60.5 KB

Then I installed the front 19MM LCA bolts along with the tow eye/guard bracket. These are torqued at this time 62ftlb.
Name:  LCA front T.jpg
Views: 132
Size:  57.7 KB

Next, I re-installed the 17MM tow eye/guard bolt up front and torqued it down along with the front bolt - 33ftlb.
Name:  Tow eye T.jpg
Views: 131
Size:  85.5 KB

At this point, I lowered the engine. I had raised the engine 1 inch before the install (marked by the tape)
Name:  time to lower.jpg
Views: 130
Size:  53.4 KB

After I lowered the engine, I measured the new engine height resulting from the new mounts. Looks like it raised the engine about 1/2".
Name:  lowered.jpg
Views: 130
Size:  53.5 KB

I removed the 4X4s and 2X4s. Someone asked what links I used for the engine support. The eye bolt is 10" long and 1/2" threads. These links are rated at over 2000lb for the small and over 3000lb for the large.
Name:  support HW.jpg
Views: 130
Size:  44.7 KB


After lowering the engine, I torqued down the 19MM lower motor mount bolt - 62ftlb.
Name:  MM T.jpg
Views: 129
Size:  70.6 KB

I also made sure the alignment holes were lined up. Normally there would be a pin here on the Porsche mounts to keep the upper and lower mount bracket fingers aligned.
Name:  pin align.jpg
Views: 130
Size:  49.9 KB

Next came the steering rack. Put the four 13MM locking studs in the crossmember from the top.
Name:  ready for rack.jpg
Views: 130
Size:  69.3 KB

I maneuvered the rack back into the crossmember channel and held it with one had while getting the reiforcement plate lined up with the 13MM studs.
Name:  rack install 1.jpg
Views: 131
Size:  83.7 KB

Then hand-tighten the four 13MM bolts to hold the plate in place
Name:  rack install 2.jpg
Views: 130
Size:  62.3 KB

Next, I installed the single short 17MM bolt at the end of the reinforcement plate (hand tightened only so that the remaining four Steering rack 17MM bolts could be lined up and assembled).
Name:  rack install 3.jpg
Views: 133
Size:  77.2 KB

Then I installed the four 17MM steering rack bushing bolts and torqued them down - 33ftlb
Name:  rack install 4.jpg
Views: 132
Size:  72.1 KB
Name:  rack install 4a.jpg
Views: 131
Size:  62.2 KB

Next, Torqued the single short 17MM bolt at the end of the plate - 33ftlb
Name:  rack install 5.jpg
Views: 132
Size:  77.3 KB

And finally, torqued the four 13MM plate nuts - 17ftlb
Name:  rack install 6.jpg
Views: 132
Size:  65.7 KB

To finish off the steering, I then re-attached the PS line clamp to the side of the engine compartment. Best to reach this from the top using a 10mm ratchet wrench.
Name:  ps lines.jpg
Views: 130
Size:  61.4 KB


Next in order was the starter wiring harness. Just a 10MM bolt here...
Name:  harness.jpg
Views: 125
Size:  79.1 KB

Then I installed the oil filter
Name:  oil filter.jpg
Views: 127
Size:  71.3 KB

The sway bar was next. I only tightened these until they were snug. Again, I read that leaving these un-torqued until the car settles is better. I just replaced the frame bushings last month but still want to lubricate them. I didn't have time to find bushing lube (WSM recommended MolyKote U - aka dry graphite molybdenum disulphide - THANKS Wally for the fancy name! - I love asking for this stuff at the local auto parts store - I just get blank stares ) I will find a supplier soon and lube them up next time they are out - which won't be long - I'm sure.
Name:  sway bracket.jpg
Views: 126
Size:  77.2 KB

Then I torqued the 19MM stabilizer link bolts at the stabilizer bar - 62ftlb
Name:  links T.jpg
Views: 126
Size:  54.6 KB

Next I torqued the 19MM lower shock mount to Lower Control Arm and stabilizer link Bolt - 62ftlb
Name:  shock mount T.jpg
Views: 126
Size:  70.0 KB

Then I replaced the air box and hooked up the air filter and air tubes.
Name:  air box.jpg
Views: 124
Size:  86.8 KB

All done underneath....
Name:  all done underneath.jpg
Views: 126
Size:  82.3 KB

At this point, I would have put the tires back on and lowered the car, put the engine cross brace back on, topped off the oil, and started it up. But I wanted to check a couple other things while the car was in the air - the flex plate tension (since I effectively raised the engine 1/2" with the new mounts) and the crank shaft end play - more on that later.

After taking the car for a drive to let the suspension settle, I brought it back and drove it up on ramps and did the final torque on the Lower Control Arm rear mounts - 19MM and they are torqued to 88ftlb. Also torqued the stabilizer frame bushing bolts - 17MM torqued to 33ftlb. Took a final drive and DONE! and WOW...I like the new mounts!!

THANKS to all that posted on doing this job before - I learned alot before even turning a wrench on this one ....and thanks to Pirtle for documenting the procedure!